Continuous and low-carbon production of biomass flash graphene.

Flash Joule heating (FJH) is an emerging and profitable technology for converting inexhaustible biomass into flash graphene (FG). However, it is challenging to produce biomass FG continuously due to the lack of an integrated device. Furthermore, the high-carbon footprint induced by both excessive energy allocation for massive pyrolytic volatiles release and carbon black utilization in alternating current-FJH (AC-FJH) reaction exacerbates this challenge. Here, we create an integrated automatic system with energy requirement-oriented allocation to achieve continuous biomass FG production with a much lower carbon footprint. The programmable logic controller flexibly coordinated the FJH modular components to realize the turnover of biomass FG production. Furthermore, we propose pyrolysis-FJH nexus to achieve biomass FG production. Initially, we utilize pyrolysis to release biomass pyrolytic volatiles, and subsequently carry out the FJH reaction to focus on optimizing the FG structure. Importantly, biochar with appropriate resistance is self-sufficient to initiate the FJH reaction. Accordingly, the medium-temperature biochar-based FG production without carbon black utilization exhibited low carbon emission (1.9 g CO2-eq g-1 graphene), equivalent to a reduction of up to ~86.1% compared to biomass-based FG production. Undoubtedly, this integrated automatic system assisted by pyrolysis-FJH nexus can facilitate biomass FG into a broad spectrum of applications.

Fabrication of carbon black nanoparticles from green algae and sugarcane bagasse.

There are several industrial uses for carbon black (CB), an extremely fine powdered form of elemental carbon that is made up of coalesced particle aggregates and almost spherical colloidal particles. Most carbon black is produced from petroleum-derived feedstock, so there is a need to find an alternative method to produce CB, which relies on renewable resources such as algae and agricultural waste. A process involving hydrolysis, carbonization, and pyrolysis of green algae and sugarcane bagasse was developed, as the optimal hydrolysis conditions (16N sulfuric acid, 70 °C, 1 h, 1:30 g/ml GA or SC to sulfuric acid ratio), a hydrolysis ratio of 62% for SC and 85% for GA were achieved. The acidic solution was carbonized using a water bath, and the solid carbon was then further pyrolyzed at 900 °C. The obtained carbon black has a high carbon content of about 90% which is confirmed by EDX, XRD, and XPS analysis. By comparison carbon black from sugar cane bagasse (CBB) and carbon black from green algae Ulva lactuca (CBG) with commercial carbon black (CCB) it showed the same morphology which was confirmed by SEM analysis. The BET data, showed the high specific surface area of prepared CB, which was 605 (m2/g) for CBB and 424 (m2/g) for CBG compared with commercial carbon black (CBB) was 50 (m2/g), also the mean pore diameter of CBB, CBG and CCB indicated that CBB and CBG were rich in micropores, but CCB was rich in mesoporous according to IUPAC classification. This study might have created a technique that can be used to make carbon black from different kinds of biomass.

Methacrylic acid in situ modified steel converter slag/natural rubber composites: Resourceful utilization of steelmaking solid wastes.

As a by-product of the steelmaking industry, the large-volume production and accumulation of steel converter slag cause environmental issues such as land occupation and dust pollution. Since metal salts of unsaturated carboxylic acid can be used to reinforce rubber, this study explores the innovative application of in-situ modified steel slag, mainly comprising metal oxides, with methacrylic acid (MAA) as a rubber filler partially replacing carbon black. By etching the surface of steel slag particles with MAA, their surface roughness was increased, and the chemical bonding of metal methacrylate salt was introduced to enhance their interaction with the molecular chain of natural rubber (NR). The results showed that using the steel slag filler effectively shortened the vulcanization molding cycle of NR composites. The MAA in-situ modification effectively improved the interaction between steel slag and NR molecular chains. Meanwhile, the physical and mechanical properties, fatigue properties, and dynamic mechanical properties of the experimental group with MAA in-situ modified steel slag (MAA-in-situ-m-SS) were significantly enhanced compared with those of NR composites partially filled with unmodified slag. With the dosage of 7.5 phr or 10 phr, the above properties matched or even exceeded those of NR composites purely filled with carbon black. More importantly, partially replacing carbon black with modified steel slag reduced fossil fuel consumption and greenhouse gas emission from carbon black production. This study pioneered an effective path for the resourceful utilization of steel slag and the green development of the steelmaking and rubber industries.

Recommendations for reporting equivalent black carbon (eBC) mass concentrations based on long-term pan-European in-situ observations.

A reliable determination of equivalent black carbon (eBC) mass concentrations derived from filter absorption photometers (FAPs) measurements depends on the appropriate quantification of the mass absorption cross-section (MAC) for converting the absorption coefficient (babs) to eBC. This study investigates the spatial-temporal variability of the MAC obtained from simultaneous elemental carbon (EC) and babs measurements performed at 22 sites. We compared different methodologies for retrieving eBC integrating different options for calculating MAC including: locally derived, median value calculated from 22 sites, and site-specific rolling MAC. The eBC concentrations that underwent correction using these methods were identified as LeBC (local MAC), MeBC (median MAC), and ReBC (Rolling MAC) respectively. Pronounced differences (up to more than 50 %) were observed between eBC as directly provided by FAPs (NeBC; Nominal instrumental MAC) and ReBC due to the differences observed between the experimental and nominal MAC values. The median MAC was 7.8 ± 3.4 m2 g-1 from 12 aethalometers at 880 nm, and 10.6 ± 4.7 m2 g-1 from 10 MAAPs at 637 nm. The experimental MAC showed significant site and seasonal dependencies, with heterogeneous patterns between summer and winter in different regions. In addition, long-term trend analysis revealed statistically significant (s.s.) decreasing trends in EC. Interestingly, we showed that the corresponding corrected eBC trends are not independent of the way eBC is calculated due to the variability of MAC. NeBC and EC decreasing trends were consistent at sites with no significant trend in experimental MAC. Conversely, where MAC showed s.s. trend, the NeBC and EC trends were not consistent while ReBC concentration followed the same pattern as EC. These results underscore the importance of accounting for MAC variations when deriving eBC measurements from FAPs and emphasize the necessity of incorporating EC observations to constrain the uncertainty associated with eBC.

Indoor and ambient black carbon and fine particulate matter associations with blood biomarkers in COPD patients.

BACKGROUND: Systemic inflammation contributes to cardiovascular risk and chronic obstructive pulmonary disease (COPD) pathophysiology. Associations between systemic inflammation and exposure to ambient fine particulate matter (PM ≤ 2.5 µm diameter; PM2.5), and black carbon (BC), a PM2.5 component attributable to traffic and other sources of combustion, infiltrating indoors are not well described. METHODS: Between 2012 and 2017, COPD patients completed in-home air sampling over one-week intervals, up to four times (seasonally), followed by measurement of plasma biomarkers of systemic inflammation, C-reactive protein (CRP) and interleukin-6 (IL-6), and endothelial activation, soluble vascular adhesion molecule-1 (sVCAM-1). Ambient PM2.5, BC and sulfur were measured at a central site. The ratio of indoor/ambient sulfur in PM2.5, a surrogate for fine particle infiltration, was used to estimate indoor BC and PM2.5 of ambient origin. Linear mixed effects regression with a random intercept for each participant was used to assess associations between indoor and indoor of ambient origin PM2.5 and BC with each biomarker. RESULTS: 144 participants resulting in 482 observations were included in the analysis. There were significant positive associations between indoor BC and indoor BC of ambient origin with CRP [%-increase per interquartile range (IQR);95 % CI (13.2 %;5.2-21.8 and 11.4 %;1.7-22.1, respectively)]. Associations with indoor PM2.5 and indoor PM2.5 of ambient origin were weaker. There were no associations with IL-6 or sVCAM-1. CONCLUSIONS: In homes of patients with COPD without major sources of combustion, indoor BC is mainly attributable to the infiltration of ambient sources of combustion indoors. Indoor BC of ambient origin is associated with increases in systemic inflammation in patients with COPD, even when staying indoors.

Long-term trends of black carbon and particle number concentrations and their vehicle emission factors in Stockholm.

Black carbon (BC) and particle number (PN) concentrations are usually high in cities due to traffic emissions. European mitigation policies, including Euro emission standards, have been implemented to curb these emissions. We analyzed BC and PN (particle diameter Dp > 4 nm) concentrations in Stockholm spanning the years 2013-2019 (BC) and 2009-2019 (PN) measured at street canyon and rooftop sites to assess the effectiveness of the implemented policies. Combining these data with inverse dispersion modeling, we estimated BC and PN emission factors (EFBC and EFPN) for the mixed fleet, reflecting real-world driving conditions. The pollutants showed decreasing trends at both sites, but PN concentrations remained high at the canyon site considering the World Health Organization (WHO) recommendations. BC concentrations declined more rapidly than PN concentrations, showing a -9.4% and -4.9% annual decrease at the canyon and -7.2% and -0.5% at the rooftop site in the years 2013-2019. The EFBC and EFPN trends showed that the mitigation strategies for reducing particulate emissions for on-road vehicles were successful over the study period. However, the introduction of biofuels in the vehicle fleet -ethanol and later rapeseed methyl ester (RME)- increased the concentrations of particles with Dp < 10 nm before the adoption of particulate filters in the exhausts. Stricter Euro emission regulations, especially with diesel particulate filters (DPF) in Euro 5, 6, and VI vehicles, led to 66% decrease in EFBC and 55% in EFPN. Real-world EFBC surpassed HBEFA (Handbook Emission Factors for Road Transport) database values by 2.4-4.8 times; however, direct comparisons between real-world and HBEFA EFPN are difficult due to differences in lower cut-off sizes and measurement techniques. Our results underscore the necessity for revising the HBEFA database, updating laboratory testing methods and portable emission measuring systems (PEMS) measurements to account for liquid condensate contributions to PN measurements.

The cross-linking between DNA damage, oxidative stress and epidermal barrier in keratinocytes after exposure to particulate matters and carbon black.

As the largest organ, the skin provides the first line of defence against environmental pollutants. Different pollutants have varied damage to the skin due to their own physical-chemical properties. A previous epidemiological study by our team revealed that eczema was positively correlated with different air pollutants. However, the mechanism of action from different pollutants on the skin is less known. In this work, the differences among the genotoxicity, intracellular reactive oxygen species, and barrier-related parameters caused by two kinds of air pollutants, that is, S1650b and carbon black (CB) were investigated by Western blot, TUNEL, comet assay and RNA-sequences. The results indicated that both S1650b and CB caused DNA damage of keratinocytes. With the content of lipophilic polycyclic aromatic hydrocarbons (PAH), S1650b leaked into the keratinocytes easily, which activated the aromatic hydrocarbon receptor (AhR) in keratinocytes, leading to worse damage to barrier-related proteins than CB. And CB-induced higher intracellular ROS than S1650b due to the smaller size which make it enter the keratinocytes easier. RNA-sequencing results revealed that S1650b and CB both caused DNA damage of keratinocytes, and the intervention of S1650b significantly upregulated AhR, cytochrome oxidase A1 and B1 (CYP1A1 and CYP1B1) genes, while the results showed oppositely after CB intervention. The mechanism of keratinocyte damage caused by different air particle pollutants in this study will help to expand our understanding on the air pollutant-associated skin disease at cell levels.

Role of circPSEN1 in carbon black and cadmium co-exposure induced autophagy-dependent ferroptosis in respiratory epithelial cells.

Carbon black and cadmium (Cd) are important components of atmospheric particulate matter and cigarette smoke that are closely associated with the occurrence and development of lung diseases. Carbon black, particularly carbon black nanoparticles (CBNPs), can easily adsorbs metals and cause severe lung damage and even cell death. Therefore, this study aimed to explore the mechanisms underlying the combined toxicity of CBNPs and Cd. We found that the combined exposure to CBNPs and Cd promoted significantly greater autophagosome formation and ferroptosis (increased malonaldehyde (MDA), reactive oxygen species (ROS), and divalent iron ions (Fe2+) levels and altered ferroptosis-related proteins) compared with single exposure in both 16HBE cells (human bronchial epithelioid cells) and mouse lung tissues. The levels of ferroptosis proteins, transferrin receptor protein 1 (TFRC) and glutathione peroxidase 4 (GPX4), were restored by CBNPs-Cd exposure following treatment with a 3-MA inhibitor. Additionally, under CBNPs-Cd exposure, circPSEN1 overexpression inhibited increases in the autophagy proteins microtubule-associated protein 1 light chain 3 (LC3II/I) and sequestosome-1 (P62). Moreover, increases in TFRC and Fe2+, and decreases in GPX4were inhibited. Knockdown of circPSEN1 reversed these effects. circPSEN1 interacts with autophagy-related gene 5 (ATG5) protein and upregulates nuclear receptor coactivator 4 (NCOA4), the co-interacting protein of ATG5, thereby degrading ferritin heavy chain 1 (FTH1) and increasing Fe2+ in 16HBE cells. These results indicated that the combined exposure to CBNPs and Cd promoted the binding of circPSEN1 to ATG5, thereby increasing autophagosome synthesis and ATG5-NCOA4-FTH1 axis activation, ultimately inducing autophagy-dependent ferroptosis in 16HBE cells and mouse lung tissues. This study provides novel insights into the toxic effects of CBNPs and Cd in mixed pollutants.

Local and NON-LOCAL source apportionment of black carbon and combustion generated PM2.5.

Current methods for measuring black carbon aerosol (BC) by optical methods apportion BC to fossil fuel and wood combustion. However, these results are aggregated: local and non-local combustion sources are lumped together. The spatial apportioning of carbonaceous aerosol sources is challenging in remote or suburban areas because non-local sources may be significant. Air quality modeling would require highly accurate emission inventories and unbiased dispersion models to quantify such apportionment. We propose FUSTA (FUzzy SpatioTemporal Apportionment) methodology for analyzing aethalometer results for equivalent black carbon coming from fossil fuel (eBCff) and wood combustion (eBCwb). We applied this methodology to ambient measurements at three suburban sites around Santiago, Chile, in the winter season 2021. FUSTA results showed that local sources contributed ∼80% to eBCff and eBCwb in all sites. By using PM2.5 - eBCff and PM2.5 - eBCwb scatterplots for each fuzzy cluster (or source) found by FUSTA, the estimated lower edge lines showed distinctive slopes in each measurement site. These slopes were larger for non-local sources (aged aerosols) than for local ones (fresh emissions) and were used to apportion combustion PM2.5 in each site. In sites Colina, Melipilla and San Jose de Maipo, fossil fuel combustion contributions to PM2.5 were 26 % (15.9 µg m-3), 22 % (9.9 µg m-3), and 22 % (7.8 µg m-3), respectively. Wood burning contributions to PM2.5 were 22 % (13.4 µg m-3), 19 % (8.9 µg m-3) and 22% (7.3 µg m-3), respectively. This methodology generates a joint source apportionment of eBC and PM2.5, which is consistent with available chemical speciation data for PM2.5 in Santiago.

A Long-Term Comparison between the AethLabs MA350 and Aerosol Magee Scientific AE33 Black Carbon Monitors in the Greater Salt Lake City Metropolitan Area.

Black carbon (BC) or soot contains ultrafine combustion particles that are associated with a wide range of health impacts, leading to respiratory and cardiovascular diseases. Both long-term and short-term health impacts of BC have been documented, with even low-level exposures to BC resulting in negative health outcomes for vulnerable groups. Two aethalometers-AethLabs MA350 and Aerosol Magee Scientific AE33-were co-located at a Utah Division of Air Quality site in Bountiful, Utah for just under a year. The aethalometer comparison showed a close relationship between instruments for IR BC, Blue BC, and fossil fuel source-specific BC estimates. The biomass source-specific BC estimates were markedly different between instruments at the minute and hour scale but became more similar and perhaps less-affected by high-leverage outliers at the daily time scale. The greater inter-device difference for biomass BC may have been confounded by very low biomass-specific BC concentrations during the study period. These findings at a mountainous, high-elevation, Greater Salt Lake City Area site support previous study results and broaden the body of evidence validating the performance of the MA350.

Effective density of inhaled environmental and engineered nanoparticles and its impact on the lung deposition and dosimetry.

BACKGROUND: Airborne environmental and engineered nanoparticles (NPs) are inhaled and deposited in the respiratory system. The inhaled dose of such NPs and their deposition location in the lung determines their impact on health. When calculating NP deposition using particle inhalation models, a common approach is to use the bulk material density, ρb, rather than the effective density, ρeff. This neglects though the porous agglomerate structure of NPs and may result in a significant error of their lung-deposited dose and location. RESULTS: Here, the deposition of various environmental NPs (aircraft and diesel black carbon, wood smoke) and engineered NPs (silica, zirconia) in the respiratory system of humans and mice is calculated using the Multiple-Path Particle Dosimetry model accounting for their realistic structure and effective density. This is done by measuring the NP ρeff which was found to be up to one order of magnitude smaller than ρb. Accounting for the realistic ρeff of NPs reduces their deposited mass in the pulmonary region of the respiratory system up to a factor of two in both human and mouse models. Neglecting the ρeff of NPs does not alter significantly the distribution of the deposited mass fractions in the human or mouse respiratory tract that are obtained by normalizing the mass deposited at the head, tracheobronchial and pulmonary regions by the total deposited mass. Finally, the total deposited mass fraction derived this way is in excellent agreement with those measured in human studies for diesel black carbon. CONCLUSIONS: The doses of inhaled NPs are overestimated by inhalation particle deposition models when the ρb is used instead of the real-world effective density which can vary significantly due to the porous agglomerate structure of NPs. So the use of realistic ρeff, which can be measured as described here, is essential to determine the lung deposition and dosimetry of inhaled NPs and their impact on public health.

[Co-exposure of carbon black and cadmium induces autophagy and inflammation in human bronchial epithelial cells via PERK pathway].

Objective: To investigate the effects of carbon black and cadmium (Cd) combined exposure on autophagy and inflammatory response mediated by protein kinase R-like endoplasmic reticulum kinase (PERK) pathway in human bronchial epithelial (16HBE) cells. Methods: In January 2022, human bronchial epithelial (16HBE) cells were resuscitated and cultured. Carbon black nanoparticles (CBNPs) were oxidized to adsorb Cd ions to construct "CBNPs-Cd" complexes. CCK-8 assay was used to detect the effects of different concentrations and time combinations of CBNPs and Cd on the viability of 16HBE cells. The subsequent dose groups were exposed to 2 µg/ml Cd, 100 µg/ml CBNPs, 100 µg/ml CBNPs+2 µg/ml Cd for 24 h. The number of autophagosomes and autolysosomes was detected by transmission electron microscopy. Western blotting was used to detect the protein expressions of PERK, eukaryotic initiation factor 2α (eIf2α), activating transcription factor 4 (ATF4), sequestosome 1 (SQSTM1/P62), and microtubule-associated protein 1 light chain 3 (LC3). After PERK gene was silenced by siRNA technology, the changes of autophagy marker proteins P62 and LC3 were detected, and the expressions of inflammatory factors interleukin-6 (IL6) and interleukin-8 (IL8) were detected by fluorescence quantitative PCR technique. One-way ANOVA analysis was used to compare three groups or more. LSD test was used for comparison between two groups. Factorial analysis was used for multivariate component analysis. Results: There was no significant change in cell viability of 16HBE after 24 h exposure to CBNPs and Cd alone or combined (P>0.05). Compared with the control group, the expressions of P62 and LC3 in 16HBE cells were significantly increased in the CBNPs and Cd alone/combined exposure group (P<0.05), and the number of autophagosomes and autophagolysosomes in the combined exposure group was increased compared with other groups. Compared with the control group, CBNPs and Cd alone exposure group had no significant effects on p-PERK/PERK and p-eIf2α/eIf2α protein expression (P>0.05). However, the protein expressions of p-PERK/PERK and p-eIf2α/eIf2α and ATF4 were all increased in the combined exposure group (P<0.05), and the levels of IL6 and IL8 in 16HBE cells in the combined exposure group of CBNPs and Cd were significantly higher than those in the control group (P<0.05). The levels of LC3 protein, IL6 and IL8 were decreased in the CBNPs-Cd combined exposure group after knockdown of PERK gene (P<0.05). The results of factorial analysis showed that exposure to CBNPs and Cd had significant effects on the expression of P62, LC3 and IL6 (P<0.05), but the interaction between the two chemicals had no statistical significance (P>0.05) . Conclusion: CBNPs-Cd combined exposure may inhibit autophagy and increase inflammation in human bronchial epithelial cells through activation of PERK-eIf2α-ATF4 pathway.

Potential source and health risks of black carbon based on MERRA-2 reanalysis data in a typical industrial city of North China Plain.

Black carbon (BC) significantly affects climate, environmental quality, and human health. This study utilised Modern-Era Retrospective Analysis for Research and Applications, version 2 (MERRA-2), which can compensate for the shortcomings of ground BC monitoring in spatial-temporal distribution to study the pollution characteristics of BC and potential pollution sources in a typical industrial city (Xinxiang) with serious air pollution in northern China. The results showed that average daily ground observation and MERRA-2 concentration of BC of 7.33 µg m-3 and 9.52 µg m-3. The mean BC concentration derived from MERRA-2 reanalysis data was higher than ground measurement due to resolution limitations and pollution from the northern regions. The reliability of the MERRA-2 data was confirmed through correlation analysis. Consideration of the spatial distribution of BC from MERRA-2 and incorporating the potential source contribution function (PSCF), concentration-weighted trajectory (CWT), and emission inventory, other possible source areas and primary sources of BC in Xinxiang were investigated. The results indicated that implementing transportation and residential emission control measures in Henan Province and its surrounding provinces, such as Hebei Province, will effectively decrease the BC level in Xinxiang City. A passively smoked cigarettes model was used to evaluate the risk of BC exposure. The percentage of lung function decrement (PLFD) was the highest in school-age children, while the impact on lung cancer (LC) health risk was comparatively lower. Notably, the BC health risk in Xinxiang was lower than in most cities across Asia.

Ambient PM2.5 components and prevalence of chronic kidney disease: a nationwide cross-sectional survey in China.

OBJECTIVES: Chronic kidney disease (CKD) is a global public health concern, and accumulating evidence has indicated that air pollution increases the odds of CKD. However, a limited number of studies have examined the long-term effects of ambient fine particulate matter (PM2.5) components on the risk of CKD among general population; thus, major knowledge gaps remain. METHODS: Using data from a nationwide representative cross-sectional survey in China and a validated PM2.5 composition dataset, we established generalized linear models to quantify the association between five major components of PM2.5 and CKD prevalence. RESULTS: There were significant associations between long-term exposure to three PM2.5 components [including black carbon (BC), sulfate (SO42-), organic matter (OM)] and increased odds of CKD prevalence. Along with an interquartile range (IQR) increment in BC (3.3 µg/m3), SO42- (9.7 µg/m3), and OM (16.2 µg/m3) at a 4-year moving average, the odds ratios (ORs) for CKD prevalence were 1.28 (95% CI 1.07, 1.54), 1.23 (95% CI 1.03, 1.45), and 1.23 (95% CI 1.02, 1.47), respectively. We did not detect any significant association of the other two PM2.5 components [nitrate (NO3-) or ammonium (NH4+)] with CKD prevalence. Stratified analyses revealed no differences (P ≥ 0.05) in the effect estimates of subgroups based on administrative region, sex, age, and other demographic characteristics. For instance, along with an IQR increment in BC at a 4-year moving average, the ORs of CKD prevalence among males and females were 1.30 (95% CI 0.98, 1.73) and 1.29 (95% CI 1.01, 1.65), respectively. The odds of CKD were generally higher with increasing PM2.5 composition concentration. CONCLUSIONS: Our study demonstrated that long-term exposure to specific PM2.5 components including BC, SO42-, and OM increased CKD risk in the general population. This study could provide new insights into source-directed PM2.5 control and CKD prevention.

The effect of the ageing process on the desorption of nonylphenol in black carbon-sediment systems: a kineto-mechanistic and modeling investigation.

Black carbon (BC) exhibits promising potential as a sediment amendment owing to its commendable adsorption capacity for hydrophobic organic contaminants (HOCs), thereby resulting in HOC-laden sediments. Desorption kinetic studies play a crucial role in comprehending the release potential of HOCs from BC-sediment systems. Although the adsorption capacity of BC for HOCs has been found to decrease with aging, there is limited research on its impact on HOC desorption kinetics. In this study, BCs derived from agricultural waste (rice straw carbon, RC) and industrial waste (fly ash carbon, FC), respectively, were used to investigate the desorption kinetics of nonylphenol (NP). Additionally, a predictive model was established using the fitting parameters obtained from the modified two-domain model. The results showed that desorption of NP was divided into three fractions: rapid fraction (Frap), slow fraction (Fslow) and resistant fraction (Fr). BCs significantly decreased, while ageing increased the desorption amount and rate of NP. The performance of RC in controlling NP release was superior to that of FC. The predicted values calculated by the established model exhibit significant positive correlations with the measured values (p < 0.01). Additionally, the correlation analysis between sorption sites and desorption fractions revealed that the concentration of NP in the desorbing fraction was nearly equivalent to that of NP in partition sites within aged sediment/FC-sediment systems. However, the aged RC-sediment systems do not conform well to this rule. In other words, the estimation of NP release risk from sediments with a strong adsorbent would be overestimated, if Frap + Fsolw is considered equivalent to the desorbing fraction.

Effect of gas temperature on carbon soot oxidation via non-thermal plasma: two-dimensional numerical study integrating reactive flow and discharge models.

Non-thermal plasma (NTP) efficiently regenerates diesel particulate filters by oxidizing carbon soot (CS) at low temperatures. However, numerical studies on the spatial characteristics of CS oxidation by NTP are scarce. In addition, the influence of background gas heating on the CS-oxidizing performance by NTP remains inadequately understood. This research investigates the impact of gas temperature (323-573 K) on heterogeneous CS oxidation using NTP in a two-dimensional configuration. The results indicate that CS is mainly oxidized by [Formula: see text], [Formula: see text], and [Formula: see text] during NTP treatment. The energy efficiency of CS removal by NTP ranges from 0.1 to 2.6 g kWh-1 for varying gas temperature and applied voltage, consistent with previous research. Higher gas temperatures enhance both CS removal rate and efficiency, whereas higher applied voltages enhance rate at the expense of efficiency. The study also assesses energy conversion efficiency from electrical power input to chemical bonding energy during CS oxidation by NTP, yielding 0.03 to 0.23% efficiency for the considered gas temperature and voltage ranges, with higher temperatures leading to better efficiency.

Constructing high-density crack-microstructures within MXene interlayers for ultrasensitive and superhydrophobic cellulosic fibers-based sensors.

Incorporating biopolymers into two-dimensional transition metal carbides and/or nitrides (2D MXene) has been demonstrated as an effective strategy to improve the mechanical behaviors of MXene-based composites. However, the insulate nature of biopolymers inevitably deteriorated the electrical conductivity and the sensitivity of assembled sensors. Herein, a novel cellulose nanofiber (CNF)/MXene/carbon black (CB) composite was demonstrated as the conductive layer in eco-friendly cellulose paper-based sensors by intercalating the CB into the MXene/CNF interlayer, followed by coating hydrophobic SiO2 for encapsulation. Befitting from the high-density crack-microstructures between CB and MXene, the fabricated superhydrophobic paper CB/CNF/MXene/SiO2 sensor delivered ultrahigh sensitivity of 729.52 kPa-1, low detect limit of 0.29 Pa, rapid response time of 80 ms and excellent stability over 10,000 cycles. Moreover, the fabricated sensor was capable of detecting the physiological parameter of human (e.g. huge/subtle movements) and spatial pressure distribution. Furthermore, the presence of SiO2 layer endowed the sensor with superhydrophobic performance (water contact angle ∼158.2 o) and stable electrical signals under high moisture conditions or even under water. Our work proposed a novel strategy to boost the sensitivity of MXene-based conductive layer in flexible electronic devices.

Upgrading recovered carbon black (rCB) from industrial-scale end-of-life tires (ELTs) pyrolysis to activated carbons: Material characterization and CO2 capture abilities.

The current study presents for the first time how recovered carbon black (rCB) obtained directly from the industrial-scale end-of-life tires (ELTs) pyrolysis sector is applied as a precursor for activated carbons (ACs) with application in CO2 capture. The rCB shows better physical characteristics, including density and carbon structure, as well as chemical properties, such as a consistent composition and low impurity concentration, in comparison to the pyrolytic char. Potassium hydroxide and air in combination with heat treatment (500-900 °C) were applied as agents for the conventional chemical and physical activation of the material. The ACs were tested for their potential to capture CO2. Ultimate and proximate analysis, Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDS), Raman spectroscopy, thermogravimetric analysis (TGA), and N2/CO2 gas adsorption/desorption isotherms were used as material characterization methods. Analysis revealed that KOH-activated carbon at 900 °C (AC-900K) exhibited the highest surface area and a pore volume that increased 6 and 3 times compared to pristine rCB. Moreover, the AC-900K possessed a well-developed dual porosity, corresponding to the 22% and 78% of micropore and mesopore volume, respectively. At 0 °C and 25 °C, AC-900K also showed a CO2 adsorption capacity equal to 30.90 cm3/g and 20.53 cm3/g at 1 bar, along with stable cyclic regeneration after 10 cycles. The high dependence of CO2 uptake on the micropore volume at width below 0.7-0.8 nm was identified. The selectivity towards CO2 in relation to N2 reached high values of 350.91 (CO2/N2 binary mixture) and 59.70 (15% CO2/85% N2).

Photo-Reactivity of dissolved black carbon unveiled by combination of optical spectroscopy and FT-ICR MS analysis: Effects of pyrolysis temperature.

Dissolved black carbon (DBC) has high photoactivity, which plays an important role in contaminants photodegradation. However, it is unclear how pyrolysis temperatures would affect the composition and photo-reactivity of DBC at the molecular level. Herein, we combined complementary techniques to study the characteristics of DBC pyrolyzed at 200 - 500 ℃, as well as the photoproduction of reactive species and the photodegradation of tetracycline (TC). Bulk composition characterization found that condensed aromatic carbonyl compounds (ConAC) with narrow molecular weights in DBC experienced an increase from 200 to 500 °C, which enhanced the photoproduction of 3DBC*,1O2, and ·OH. Molecular-level data suggested that 3DBC* and 1O2 were both related to the same DBC compounds. Comparatively, the patterns for ·OH were less pronounced, implying its precursor was not 3DBC* and had more complexity. Plentiful CHOx species of ConAC in DBC400 and DBC500 (DBCT, where T = pyrolysis temperature) accelerated the generation of 3DBC* and 1O2, enhancing the photodegradation of TC, and mainly triplet states of quinones reacted with TC. In contrast, DBC200 and DBC300 exhibited inhibition since massive CHOx species in lignin-like reduced 3TC* to TC. Our data revealed the diverse photochemical behavior mechanisms of DBC pyrolyzed at 200 - 500 ℃ at the molecular level and the implications for aquatic contaminants photochemistry.

Effects of a liquefied petroleum gas stove intervention on stillbirth, congenital anomalies and neonatal mortality: A multi-country household air pollution intervention network trial.

Household air pollution (HAP) from cooking with solid fuels used during pregnancy has been associated with adverse pregnancy outcomes. The Household Air Pollution Intervention Network (HAPIN) trial was a randomized controlled trial that assessed the impact of a liquefied petroleum gas (LPG) stove and fuel intervention on health in Guatemala, India, Peru, and Rwanda. Here we investigated the effects of the LPG stove and fuel intervention on stillbirth, congenital anomalies and neonatal mortality and characterized exposure-response relationships between personal exposures to fine particulate matter (PM2.5), black carbon (BC) and carbon monoxide (CO) and these outcomes. Pregnant women (18 to <35 years of age; gestation confirmed by ultrasound at 9 to <20 weeks) were randomly assigned to intervention or control arms. We monitored these fetal and neonatal outcomes and personal exposure to PM2.5, BC and CO three times during pregnancy, we conducted intention-to-treat (ITT) and exposure-response (E-R) analyses to determine if the HAPIN intervention and corresponding HAP exposure was associated with the risk of fetal/neonatal outcomes. A total of 3200 women (mean age 25.4 ± 4.4 years, mean gestational age at randomization 15.4 ± 3.1 weeks) were included in this analysis. Relative risks for stillbirth, congenital anomaly and neonatal mortality were 0.99 (0.60, 1.66), 0.92 (95 % CI 0.52, 1.61), and 0.99 (0.54, 1.85), respectively, among women in the intervention arm compared to controls in an ITT analysis. Higher mean personal exposures to PM2.5, CO and BC during pregnancy were associated with a higher, but statistically non-significant, incidence of adverse outcomes. The LPG stove and fuel intervention did not reduce the risk of these outcomes nor did we find evidence supporting an association between personal exposures to HAP and stillbirth, congenital anomalies and neonatal mortality.